а это ?
---------- Post added at 20:36 ---------- Previous post was at 20:35 ----------
Free Energy Generators
Electric loop free energy generator
The electric loop free energy generator is one of the most simple free energy generator topologies. It works on a principle of an endless electric loop. Once the initial energy is applied, the electric power keeps circulating in the ring. The circulation also starts the process of harnesing the ubiquitous abundant energy, thus turning the device into an overunity. Overutiny state allows adding a load without draining the energy from the circle. This turns the ordinary energy circle into a free energy generator and generates some amount of the free electricity. Big advantage of this version of free energy generator is that it has no moving parts. It simple uses the circular coil made of a multi-conductor wire. The electricity is the only thing moving in the generator. The disadvantage is that the free energy device of this kind can't be simply started by spinning its rotor, unlike the rotation free energy generators. The source of an initial electric energy is necessary. The Electric loop free energy generator topology is suitable for building the low to medium power overunity device.The practical model of this generator is easy to build using the ordinary power extension plug. In most cases, the cable length of at least 3 meters (10 feet) is enough to form its operating coil. I recommned the coil diameter to be at least 10cm (4 inch) and the turn count at least 8 turns. The complete circle is formed by putting the end of the cable into one of the sockets. The free energy device is ignited by using a source of initial electricity. The voltage has to be high enough to start the circulation at the overunity level. The best ignitor seems to be simply the piezo from the electric lighter. It allows the ignition witn ho battery (that can run empty), just by pressing the button of the piezo element. This element generates high voltage sparks of several kilovolts, but with a very short duration and very low current. The output wire shoud be put very close to a metal part of the extension cord. Best way is to use metal parts accessible from outside, eg. the ground contact. The electromagnetic pulse is then induced into the other wires of the extension socket, eg. the line and neutral. Before doing anything, read the Disclaimer first.
The ilustration how the power extension cord can look like. It has several sockets. Note the maximum power rating denoted on it. This power should never be exceeded. However, in some cases, the generated power limit of the free energy generator can be lower due to the coil dimensions.
Beside the power extension plug, another necessary part of the free energy generator is the lighter. The image shows the comparison of the good and wrong lighters. The blue one is the good one - the piezo can be salvaged from it. The orange one is the bad one - it is the mechanical lighter, not electrical, and contains no piezo. So remember, not every lighter is suitable as a source of an initial energy!
Those photos illustrate the overunity generator before and after the ignition. I strongly recommend you to use the power strip with the indicator light in its switch. The light helps you determine Whether the generator is in active mode or in idle mode. Also remember to turn on the switch before ignition. The ignition can take up to several cycles of the piezo pulse.
Those two pictures are showing the detail of the piezo and the free energy being started in dark. You can see the visible high voltage electric spark. Also note that the piezo, unlike the non-overutiny elements, has only a single wire and no return wire.
Last pair of the photos shows the electric loop free energy generator in loaded state. It can be loaded even with a 2 kW heating unit!
---------- Post added at 20:37 ---------- Previous post was at 20:36 ----------
The batteries, lens, mirror and magnet - the material to build the electrostatic free energy motor. At the right, the circle in construction.
The circle almost complete. At the right photo, the mirror inside the electrostatic circle.
Putting the wireless homopolar free energy motor into operation.
The operating free energy generating motor with the rotor turning counter clockwise.
---------- Post added at 20:37 ---------- Previous post was at 20:37 ----------
A computer fan can be used to build a small prototype of the magnet motor. You can se the motor before disassembly (left) and after disassembly (right).
The picture on the left is showing the motor coils originally used to generate the magnetic field. We can replace the coils using the neodymium magnets. The magnets have to be placed into the same directions, where the original coils were. This ensures that the magnetic field orientation, necessary for the motor operation, remains the same. In this motor, there are four coils, thus we need to use four magnets. On the right picture you can see the hadr drive and the neodymium magnet you can salvage from it for free.
The magnets placed into the directions of the coils. The magnet motor running, needing no electric power. Note: The coils don't need the electric power any more. The can generate it! But remember, this is a very small unit, so only a little power can be generated. In case you need only the wind from the fan, you can cut the cable.
Another prototype of the magnet motor, with the magnets attached using a sticky tape, forming a portable unit.